Özel Uygulamalar

The FSR-07 has a recoater and mandrel proof testing.This model is appropriate not only for recoating but also reliability proof testing as well as tension testing to failure.

The ReCoater 2 is used to restore the protective coating on acrylate coated optical fibers in high strength applications. Molds are available in different sizes to cover a range of coating diameters and can easily be exchanged by the operator with no realignment required. Custom molds are available upon request.

Nyfors Producrts.The extended length ReCoater 2 XL is used to restore the protective coating on acrylate-coated optical fibers in high strength applications. Designed to process long sections of stripped fiber, it accepts silicone molds of up to 110 mm length.

Nyfors product. This compact and easy-to-use recoater is extremely portable and allows for quick and easy recoating of optical fibers. NYFORS silicone mold technology provides extreme flexibility for a variety of recoating needs.

Nyfors Product. Designed for high strength applications, the AutoCoater 2™ restores the protective coating on spliced acrylate-coated optical fibers. It is fully automatic, allowing for operator skill independence in factory environments with high productivity and cost advantages.

Nyfors product. The AutoCoater 2 SC™ is used to restore the protective coating on acrylate coated optical fibers in high strength applications. It is fully automatic, allowing for operator skill independent operation in factory environments with high cost and productivity advantages. This modified version of the automatic AutoCoater 2™ is equipped with special clamps for recoating applications where only short lengths of fiber are available. A narrower positioning and shorter distance between the fiber clamps than in the standard version enables clamping and recoating of fibers as short as 124 mm without reducing the recoat length itself.

Fiber holder FH-100 series are for Fujikura fusion splicer FSM-100 resies, FSM-40F/PM and FSM-45 series. The FH-100 series are supplied with a pair.

The Fiber holder FH-40-LT900 is exclusively designed for holding loose tube buffered fiber by Fujikura's fusion splicer,FSM-100 series, FSM-45 series, FSM-40F and FSM-40PM. The FH-40-LT900 holds the loose tube bufferd fiber by tightening a screw in the lid. The FH-40-LT900 is supplied with a pair.

The CleaveMeter 3DTM is a phase-shifting Michelson interferometer for non-contact end-face inspection of cleaved and polished optical fibers with cladding diameters up to 1200 μm. Designed for both production and research applications, this comprehensive fiber optic testing system combines full resolution, three-dimensional surface topography reconstruction and mapping with automated, operator independent measurements of cleave angle and surface flatness in a small, lightweight benchtop unit.

The CleaveMeterTM interferometer system is designed for inspecting the surface quality, flatness and perpendicularity of cleaved and polished optical fibers. Complementing the NYFORS AutoCleaverTM line of automatic fiber cleavers with process documentation and optimization functionality, it allows every cleave to be individually inspected and evaluated even in high volume production environments.

Nyfors product. The AutoCleaver S1™ senses the edge of the coating to automatically adjust the bare fiber length after cleaving. This feature is valuable when a specific and accurate bare fiber length is required. The requested bare fiber length is specified by the customer at order and can be fine tuned by software between 0 and 500 μm.

Nyfors product. The AutoCleaver S2 is a modified version of the NYFORS automatic fiber cleaver, designed for the cleaving of air-clad fibers. It provides outstanding cleaving performance for fi bers from 125 μm up to 1000 μm in diameter. A unique and patent pending cleaving process generates typical cleave angles of less than 0.5 degrees.

Nyfors Product. The AutoCleaver LDF™ (Fujikura edition) is a high precision fiber cleaver, designed for cleaving of large diameter fiber (LDF). It provides outstanding cleaving performance for large diameter fibers from 230 μm up to 1000 μm in diameter. The unique and patent pending cleaving process generates typical cleave angles of less than 0.5 degrees.

Nyfors Product. The AutoCleaver LDA is an automatic system for precision cleaving of circular large diameter fibers (LDF). It is a special version of NYFORS’ well known large diameter cleaver designed for both perpendicular and angled cleaving of fibers ranging from 230 up to more than 800 μm in diameter.

This fully automatic optical fiber cleaver is designed for fast and flexible fiber processing in factory and laboratory environments. Easily interchangeable fiber handling parts enable high precision cleaving of different fibers in the range from 80 μm up to 600 μm cladding diameter with industry leading repeatability and consistency.